INNOWATECH Anolyte® is produced from drinking water, pure salt and electricity by means of membrane cell electrolysis.

• Highly effective and pH-neutral. Consists of approx. 80% hypochlorous acid.
• High stability and sustained effect
• Breaks down biofilms and prevents their reformation
• No use of hazardous goods or water-polluting substances (AwSV)
• Low risk regarding the formation of unwanted by-products
  (THM, chlorate, chlorite, AOX)
• No increased risk of corrosion and no damage to elastomers
• Operating substances water and salt are available worldwide
• Very low cost of approx. €5.00 for 1,000 l of Anolyte® concentrate

Only the following is required on-site to generate Anolyte® concentrate:

• Water connection
• Wastewater connection
• 230VAC

Based on your application data and consumption, the size of the following system components is determined:

• Softening / reverse osmosis / brine preparation
• Control / Anolyte® generation
• Anolyte® concentration / storage tank
• Anolyte® dosing pumps

To produce Anolyte®, water is treated to ultrapure water via a softening system / reverse osmosis, and a 0.4 - 0.5% salt solution is generated via brine preparation.

With INNOWATECH membrane cell electrolysis, Anolyte® is continuously produced (~80-95%) via a semipermeable membrane. Approximately 5-20% catholyte surplus (aqueous NaOH solution) is discharged (without post-treatment).

During this process, the following always applies:

• pH range always > 6.7
• no chlorine gas
• no outgassing

The highest purity of the active agent Anolyte® (75-85% HOCl) is produced using this process and stored in the Anolyte® storage tank for your cleaning processes.

Anolyte® is always produced in the optimal pH range. This means there is neither a risk of corrosion from the release of chlorine nor any loss of activity as with sodium hypochlorite.

INNOWATECH Anolyte® is highly efficient and, due to its minimal content of elemental chlorine, compatible with all common installation materials.

INNOWATECH Anolyte® is certified and tested according to European standards to the following norms:

• DIN EN 13697, DIN EN 1276, DIN EN 13623 - Bactericidal, e.g. MRSA, Escherichia coli, Enterococcus hirae, Pseudomonas aeruginosa, Staphylococcus aureus, Legionella pneumophila
• DIN EN 13624 - Yeasticidal, e.g. Candida albicans
• DIN EN 13704 - Sporicidal, e.g. Bacillus subtilis
• DIN EN 14476 - Virucidal, e.g. murine norovirus, adenovirus, poliovirus
• etc.

The effectiveness of Anolyte® when used within the scope of the Drinking Water Ordinance is sufficient to eliminate contamination of drinking and process water systems with Legionella, Pseudomonas, E. coli and other water-polluting germs within a few hours/days. Shock disinfection can eliminate contamination within a few minutes.

You are welcome to request the relevant certificates from us at any time:

With INNOWATECH's innovative Smart-Aquadron® technology, Anolyte® is produced with reduced chlorate levels and on demand – from pure raw materials such as salt and water. Membrane-divided electrolysis cells, special anode coatings and an optimized cell design result in an active agent with a minimal proportion of chlorate and other by-products.

The intelligent control via the Aquadron® touch panel ensures precise, automated adjustment of production to actual demand. Radar sensors precisely measure the fill level, and programmable level settings and predictive calculations prevent chlorate formation during storage.

This system is part of the "Cyber-Physical Systems – Smart-Aquadron®" project in cooperation with Fraunhofer IPA Stuttgart and sets new standards in safety, efficiency and sustainable water treatment.

Your benefits:

• Chlorate-reduced production for maximum hygiene
• Demand-driven production for the highest efficiency
• Just-in-time technology for fresh, pure active agents
• Cooperation with Fraunhofer IPA for innovative standards

The membrane cell electrolysis and INNOWATECH Anolyte® used in the INNOWATECH Aquadron® comply with

• the requirements of the Drinking Water Ordinance
• the purity requirement according to DIN 901
• DIN EN 17818
• the requirements of DVGW Code of Practice W 229

The pH-neutral active agent INNOWATECH Anolyte®, classified as sodium hypochlorite, is listed in the list of treatment substances and disinfection processes under § 20 of the German Drinking Water Ordinance for the intended use of "disinfection".

INNOWATECH GmbH is included as an authorized active substance producer in the Article 95 list under the EU Biocidal Products Regulation (EU No. 528/2012).

The relevant DVGW codes of practice and other laws, standards and guidelines regarding water treatment for "water intended for human use" are complied with during the planning, manufacturing, commissioning and maintenance of INNOWATECH Aquadron® systems.